Search the Blog for Certain Topics

Thursday, January 7, 2010

Flashing Samsung JET


INSTRUCTIONS (COURTESY DARKFORESTGROUP)




This is for experimental use only, Flash At Your Own Risk!!!! You can not back up your original firmware, so you will loose any applications install by your provider.

SIM LOCK or NETWORK LOCK
First thing to check is that your phone does not have simlock! If it does, you MUST take your phone to a shop that can remove it. It is not expensive but MUST be done first or you will FREEZE your phone. If you freeze you phone it will cost you even more to get it fixed! Just type *#7465625# and look for Sim Lock or Network and make sure it says OFF.

Prepare the PC

Here you must download the essentials. First download Samsungs New PC Studio This contains the drivers you for the computer to recognize the phone in bootloader mode. When you download go ahead and install it, when it is finished restart the computer and plug up your phone. If NPS dose not start on its own it OK just start it by clicking the icon. When it comes up it should recognize your phone, IF IT Does NOT, unplug the phone and set it for “mass storage” then try it again and should work. Next download the Multiloader it is the software you will use to flash your phone. Last, download the firmware you want.  Once the firmware is downloaded then unzip it to a location you can easily find it on your computer.

Prepare Your Phone
Back up every thing you dont want to loose! Every thing! Even phone numbers and pictures! So many people have failed to do this and there is no way to recover it! After you back up do a Hard Reset on your phone. Type *2767*3855# and wait for the phone to restart. After it restarts, let it sit about 3 min before proceeding.
Multiloader
Before you connect the phone to the computer, turn it off and put in bootloader mode. Depending on your phone this can be done in several different ways, so refer to the flash guide for this step.
Now you are ready for the flash guide! Click here to proceed
Good Luck!!!

Step 1 You must follow this step!!!!


------------------------------------Set Up Your Computer------------------------------------------

1. Install NPS on your computer and make sure it will communicate with your phone.
2. Disconnect your phone and Close NPS.
3. Click "Start" or the Windows logo on the bottom left of your computer screen and click in the search/run box and type msconfig.
4. Select the tab marked "Start Up" and click "disable all" and click ok.
5. Restart the computer and you are ready to flash.

DO NOT! run NPS again until you have successfully flashed your phone! After you have successfully flashed your phone, you must reset the Windows setting back to there original and restart your computer.



-------------------------------------Now continue with the flash----------------------------------


WARNING!
Make sure your phone does not have sim lock before you try and flash.
Type *#7465625# and make sure the SIMLOCK is OFF, if it is ON you MUST
take it to a shop and have it removed or you will freeze your phone!


First thing to always remember, is BACK UP YOUR PHONE, Pictures,wallpapers,
music, and any contacts you have saved on your phone. I am not responsible
for any damage to you, your phone, computer, or lost of data in this process.
This is a guideline intended for professional technicians.
USE AT YOUR OWN RISK!!!

What you will need:
1. USB cable that came with your phone.

2. New Samsung NPS

Install this software first, it contains the drivers for your phone, and has every thing you need for backup.

3. Multiloader 5.56

http://www.ziddu.com/download/8199103/MultiLoader_V5.56_2.rar.html

4. New firmware

http://www.mediafire.com/file/zwnzizzzdmj/S8000XEII2.rar
 


-----------------------------Now you are ready to begin-----------------------------------

1. Make sure Samsung PC Studio is installed and communicates with your phone. And unpack
the firmware in a folder you can easily find it.
2. Remove the Sim and MicroSD from your phone and replace the battery.
3. MAKE SURE THE PHONE IS OFF AND NOT CONNECTED TO THE COMPUTER.
4.  Hold down the "Volume -" button on the left  side ,
and the "Camera" button on the right, then press the "Power" button = all three buttons
need to be pressed together. Your phone should start up into a red\blue on black bootloader screen.)
5. Now run MultiLoader v5.54
6. Plug the phone up to the computer.

---------------------------------Multiloader Steps------------------------------------------

1. Select the radio button FOR JET= LSI6410
2. Select Boot Change
3. Full Download
4. Master rom

5. Then click Boot, and select the boot files from the unpacked firmware folder.

6a. Select Amss

6b.Select Apps


7. Rsrc1

8. Rsrc2(Low) Do not use! (Mid).r2c.  (Warning! phone may not restart if you select mid)

9. Select the Factory FS file.

***FOTA and ETC fields are left blank.****

10. Click the Port Search button, it will find your phone and show the com port is ready.

11. Click the download button and be patient, this will only take a few minutes to complete.

12. When it's finished, it will show "ok complete".

13. Unplug the phone from the USB cable, reinstall the sim and SD card.
*** NOTE Some models and some will not, if yours does not restart at this point, take out the battery a few seconds then reinsert it. NOTE ***

14. Now with every thing is complete, You can perform a hard reset by typing *2767*3855# into the hand set
(but not necessary.)
15. When the phone resets type *#1234# into your handset to check your new firmware ver. 


***NOTE!***
If your phone fails the flash for any reason, DO NOT TRY AND RESTART IT!!!!! Restart the computer
and try the flash again!


You need to perform the camera firmware update, Admin codes have been changed on recent FW:
   a. Type *#197328640# in the Idle mode, then you can reach the test mode.
   b. Select [6] Video
   c. Select [3] Camera Firmware update
   [Please Wait] will be displayed.

   Wait a few minutes then [Please Wait] will be changed to [SUCCESS]



The video is meant for viewing purpose only. Please do not try to flash your phone as you may lose the phone warranty.

Flashing will  result in loss of data ,phone contacts and customized settings.











14 comments:

  1. hi man i have just flash it

    but i lost the Arabic language

    i need it man
    u didn't say that i will lost the Arabic
    please man i need it

    ReplyDelete
  2. May i know what happen if my update firmware show [fail]..then my memory card cant be read

    ReplyDelete
  3. Hi dere,

    i was planning to flash my jet but in your above video after you open multiloader you have selected some files which i was not able to understand what are those files?.cause what you've mentioned is to get only the firmware file, so i suppose it should be only one file. please help.

    thanks in advance.

    ReplyDelete
  4. Hi there, Thanks for the guide.. Infact, the whole website is fantastic, really good idea, cheers.

    I'm now on the new firmware. I much prefer it to the old; moving the menu icons about is great, and I think it feels a bit faster too :).
    I had a couple of problems flashing, but thankfully i just tried again and it seemed to work. First one was "amss fail", and the second was, when it rebooted the phone before flashing, it swapped com ports... If anyone encounters those errors when flashing, It seemed to work out fine for me, I just restarted the PC, and turned on the phone in bootloader mode again. Third time it worked!.. Oh and I turned off my antivirus, not sure it that was actually contributing to those errors though, could be just a coincidence ;)
    Also, to Gen8tic Freak, all the files you mention that you have to select in multiloader are packed up in the .zip file to begin with, so just unzip it to a common folder, and then browse to it each time with multiloader. The files will all be in there. They should be relatively easy to find as most of the time it'll filter by file type and you'll only get one choice (the file you need!). The first one (the boot files), you only have to select the folder "BOOTFILES".
    Hope that helps

    ReplyDelete
  5. Can you tell what are the new things in the latest FW released this year ?
    your site seems to be having some probs.
    thanks

    ReplyDelete
  6. hi there...implanning to update my fw coz i think the nps of samsung dont have the latest update for samsung jet...i just want to ask..is it also safe if i install the S800MDXIL3 FW version rather than S8000XEII2 coz i think that it is more updated...is the fw code for this king of firmware change???for the FW upgrade of the cam?

    ReplyDelete
  7. really worked, 100% many thanks man, you saved me, i had a problem with the software rebooting, now it's fixed, fast and has lots of new stuff.. thanx a lot, althought, I WASN'T ABLE TO UPDATE THE CAMERA FIRMWARE ... IT SAYS FAILED .. I DON'T KNOW WHY, ANY HELP PLEASE.

    ReplyDelete
  8. i have as well problem update the camera i see is usual HELP PLEASE someone

    ReplyDelete
  9. Please Can you tell me what's the best firmware That contains French Arabic And english ...
    Many thanks !

    ReplyDelete
  10. some1 pls help as my phone is stuck on a fizzled screen as the multiloader failes

    ReplyDelete
  11. hey i have a sound problem in my samsung jet s8003, can anyone help me to fix this,....

    ReplyDelete
  12. stuck on fan club and boot again, what is wrong Dude

    ReplyDelete
  13. Stuck on fun club logo.... please help me guys.... I really need this phone to be alive....
    Contact - culdi27@gmail.com

    ReplyDelete